VanMoof Error Codes

BAT_SCP

Short circuit protection
(main battery related)

BAT_MOTP

Mosfet over temperature protection
(main battery related)

BAT_PDSCP

Pre discharge short circuit protection
(main battery related)

BAT_PDOCP

Pre discharge overload circuit protection
(main battery related)

BAT_UVP2

Under voltage protection 2
(main battery related) (try charging for a longer period, could solve issue)

BAT_UVP1

Under voltage protection 1
(main battery related)

BAT_OVP2

Over voltage protection 2
(main battery related)

BAT_OVP1

Over voltage protection 1
(main battery related)

BAT_COCP1

Charge over current protection 1
(main battery related)

BAT_COCP2

Charge over current protection 2
(main battery related)

BAT_DOCP2

Discharge over current protection 2
(main battery related)

BAT_DOCP1

Discharge over current protection 1
(main battery related)

BAT_CUTP

Charge under temperature protection (main battery related) (it's too cold to charge)

BAT_COTP

Charge over temperature protection (main battery related) (it's too warm to charge)

BAT_DUTP

Discharge under temperature protection
(main battery related) (it's too cold to discharge)

BAT_DOTP

Discharge over temperature protection
(main battery related) (it's too hot to discharge)

BAT_FP

Permanent fail (fuse burn)
(main abttery related) (likely socket short circuit)

BATTERY_NO_DSG

Could not set discharge mode
(main battery related)

BATTERY_MISSING

Signal bat_key_in is low
(main battery related)
(battery not recognized, also the error you get when no battery is present)

BATTERY_COMMUNICATION

Modbus battery
(main battery related)

BATTERY_NO_OUTPUT

BMS seems to shutdown
(main battery related)

NO_CHARGE_CURRENT

Charging state but no current reported
(main battery related)

MOTOR_COMMUNICATION

SSP TI Motor chip
(module related)

BLE_COMMUNICATION

SSP BLE chip
(module related)
(Bluetooth chip)

OAD_ABORT

transfer from app aborted
(Module related)
(Upload was aborted?)

OAD_CRC

transferred image crc error
(Module related)

OAD_TRANSFER

OAD file transfer took too long
(Module related)

OAD_PACK

No or invalid file in pack
(Module related)

ICF_TIMEOUT

Timeout during flash programming
(Module related)

ICF_HEADER

Header not found
(Module related)

ICF_NO_FILES

No files in pack
(Module related)

ICF_ERASE

Flash erase error
(Module related)

ICF_WRITE

Flash write error
(Module related)

ICF_CRC

File in pack has crc error
(Module related)

PGM_MOTORWARE

Programming of the motor controller failed

PGM_BATTERYWARE

Programming of the BMS controller failed

PGM_SHIFTERWARE

Programming of the shifter controller failed

PGM_BLEWARE

Programming of the BLE controller failed

INTERNAL_BATTERY

STVC3115 read error, lipo might be missing
(Module related)
(check if batt. module is charg.)

READ_LIGHT_SENSOR

CM3232 I2C read error
(Module related)
(light sensor)

STUCK_HORN_BUTTON

Pressed longer than x seconds
(Button)(Button or cable, water or short circuit)

STUCK_BOOST_BUTTON

Pressed longer than x seconds
(Button)(Button or cable, water or short circuit)

KL_COIL_MISSING

Kick-Lock coil not deteted

SHIFTER_NOT_IN_GEAR

After 10 tries, gear has not been reached

SHIFTER_COMMUNICATION

Modbus Shifter
(Shifter not recognized)
(Plug in tester Shifter)

MOTOR_MOTOR_CABLE

Bit2/NTC motor cable not connected
(Motor not recognized)

MOTOR_MOTOR_OVER_CURRENT

DRV8301 over temperature (bit6)

MOTOR_CONTROLLER_ERROR

Error in user parameters (bit8)(replace motor)

MOTOR_CURRENT_ERR

Current offset calc. +-rom default value 1.0

MOTOR_VOLTAGE_ERR

Voltage offset calc. +*ram Vbat/2 or Vbat